The "WizardProg Mobile" (professional version application is "WizardProg Expert") application software designed to manage the programming operation for the universal portable USB-programmer TL866A/CS and other programmer models which fully compatible with it. This system is used to program a wide range of E(E)PROM chips, microcontrollers internal EEPROM, testing SRAM chips and logic chips.
The application allows you to achieve a new level of mobility and efficiency when using the programmer TL866, which is used widely to repair and adjustment:
· automotive computers, computer-unit and radio;
· personal computers;
· any other modern electronic equipment.
The "WizardProg Mobile" system is used by service technicians of electronics, amateur radio operators and developers of modern electronic devices for the purpose of:
· repair and restore the microelectronic device and firmware;
· promptly update the firmware of microelectronic devices;
· assist in the embedded electronics construction and setting up the microcontroller units;
· replicate numerous useful designs using advanced electronic components.
Main characteristics and features of the "WizardProg Mobile" microelectronic programming system are:
· Fast and reliable programming, in most cases with significantly better speed than the similar systems.
· The programmer's low power consumption when powered by USB (OTG)-cable from the mobile device battery.
· Support for a wide range of integrated circuits (ICs): the memory of a large capacity up to 128Mbit (EPROM, FLASH, EEPROM I2C/3-wire/SPI), microcontrollers PIC, Atmel-AVR, MCS-51 based SST, SyncMOS, Winbond. PLD chips, GAL.
TL866 programmer does not need an external power supply and it operates using the power sources of a tablet or mobile phone which is connected to via USB interface. Physical linking to a mobile device is provided with a USB cable fully supporting OTG (On-The-Go) protocol.
Important note! The target control tablet or mobile phone must have a fully implemented hardware support of OTG access too!
Currently "WizardProg Mobile" mobile application is completely autonomous in operation, does not need a permanent connection to the Internet, allowing you to use it even without access to communication networks.
Both of programmer's models TL866CS and TL866A(ICSP) are fully supported. The modern version of the TL866II Plus programmer currently is not supported by the "WizardProg Mobile" system!
Device list for the current application version: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm
Perangkat lunak aplikasi "WizardProg Mobile" (aplikasi versi profesional adalah "WizardProg Expert") yang dirancang untuk mengelola operasi pemrograman untuk pemrogram-universal USB portabel TL866A / CS dan model pemrogram lainnya yang sepenuhnya kompatibel dengannya. Sistem ini digunakan untuk memprogram berbagai chip PROM E (E), mikrokontroler EEPROM internal, menguji chip SRAM dan chip logika.
Aplikasi ini memungkinkan Anda untuk mencapai tingkat mobilitas dan efisiensi baru saat menggunakan programmer TL866, yang digunakan secara luas untuk memperbaiki dan menyesuaikan:
· Komputer otomotif, unit komputer, dan radio;
· komputer pribadi;
· Peralatan elektronik modern lainnya.
Sistem "WizardProg Mobile" digunakan oleh teknisi layanan elektronik, operator radio amatir dan pengembang perangkat elektronik modern untuk tujuan:
· Memperbaiki dan mengembalikan perangkat dan firmware mikroelektronik;
· Segera memperbarui firmware perangkat mikroelektronik;
· Membantu dalam konstruksi elektronik tertanam dan mengatur unit mikrokontroler;
· Mereplikasi berbagai desain yang berguna menggunakan komponen elektronik canggih.
Karakteristik dan fitur utama dari sistem pemrograman mikroelektronik "WizardProg Mobile" adalah:
· Pemrograman yang cepat dan andal, dalam banyak kasus dengan kecepatan yang jauh lebih baik daripada sistem serupa.
· Konsumsi daya rendah programmer saat ditenagai oleh USB (OTG) -kabel dari baterai perangkat seluler.
· Dukungan untuk berbagai rangkaian terintegrasi (IC): memori berkapasitas besar hingga 128Mbit (EPROM, FLASH, EEPROM I2C / 3-wire / SPI), mikrokontroler PIC, Atmel-AVR, MCS-51 berbasis SST, SyncMOS, Winbond. Chip PLD, GAL.
Programmer TL866 tidak memerlukan catu daya eksternal dan beroperasi menggunakan sumber daya tablet atau ponsel yang terhubung melalui antarmuka USB. Tautan fisik ke perangkat seluler dilengkapi dengan kabel USB yang sepenuhnya mendukung protokol OTG (On-The-Go).
Catatan penting! Tablet kontrol target atau ponsel harus memiliki dukungan perangkat keras yang sepenuhnya diimplementasikan dari akses OTG juga!
Saat ini aplikasi seluler "WizardProg Mobile" sepenuhnya beroperasi secara otonom, tidak memerlukan koneksi permanen ke Internet, memungkinkan Anda untuk menggunakannya bahkan tanpa akses ke jaringan komunikasi.
Kedua model programmer TL866CS dan TL866A (ICSP) didukung penuh. Versi modern dari programmer TL866II Plus saat ini tidak didukung oleh sistem "WizardProg Mobile"!
Daftar perangkat untuk versi aplikasi saat ini: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm